DAS NX-148E LCD Codepad Manuale Utente

NX-148 LCD CODE PADTABLE OF CONTENTSGlossary Of Terms ... 4Understanding The Lights ...

10bypass light will stop flashing upon exiting the Bypass Mode.Pressing the scroll keys will display all bypassed zones.• –Press the

11Procedure #2: If you do not know the number of the zone you wish to bypass,use the following steps:Step 1 Press The description

12Raise tone ººLower tone ºAlarm Memory 1ZONE 1WALK-TEST MODEStep 1 Press [r] [Chime].Step 2 Enter a “Master Arm/Disarm C

13TEST FUNCTION (Optional, if programmed)If programmed, this function will perform a battery test, communicator test,and/or a siren test. No alarms wi

14Photo layout (Page 12 & 13)

15Photo layout (Page 12 & 13)

16ASSIGNING USER CODE AUTHORITY LEVELSAssign authority levels to users by following the steps below. Assign usercodes before assigning authority lev

17

18Open 759/25 17:57 P3rrRESET FUNCTIONThis function is used to reset Smoke Detectors, Zone Troubles, a

19ADJUSTING THE VIEW / BRIGHTNESS OF THE LCDStep 1 Enter The LCD Screen will prompt for a code.rr 9 1Step 2 Enter [master code]. The

2 ZONE DESCRIPTIONS 01 ____________ 17 ____________ 33 ____________02 ____________ 18 ____________ 34 ____________03 ____________ 19 ____________ 35 _

20

21MULTI-AREA SYSTEMS OPERATIONIf your system is multi-area and the code pad resides in one area, your codepad will provide the status of the zones in

22Ready 12345678Armed 1234-678System ReadyType code to arm1--4 --8 Disarm ºº--3- 67- Arm ººDISPLAYS IN THE MU

2312-4--78 Disarm ºº--3-56-- Arm ººArea 5 ReadyType code to armDash (-)Area #Area is Armed• To arm all of the areas, press the

24If the code pad is sounding an alarm or the siren is running, it can besilenced by entering a code with the authority for the area(s) that are inala

25Service RequiredType rr2 for helpControlOver-currentControlSiren troubleControlBox tamperControlPhone troubleControlFail to Comm.ControlGround fault

26ControlLow BatteryThe standby battery is low.

27ExpansionOver-currentExpansionAux. comm. failExpansionPower troubleExpansionLow BatteryExpanderBox tamperExpansionTroubleExpansionSiren troubleZoneT

28identify the zone.KEYPAD CONTROL TONES (BEEPS)A sounder is built into the keypad and may sound for any of the followingreasons: # Beeps for all key

29EMERGENCY ACTIVATION KEYSNOTE: You must hold these keys for 2 seconds to activate these functions.Your system may not be programmed for these activa

3THIS MANUAL IS PROVIDED TO HELP YOU UNDERSTAND YOUR SECURITY SYSTEMAND BECOME PROFICIENT IN ITS OPERATION. ALL USERS OF YOUR SECURITYSYSTEM SHOULD R

30EMERGENCY EVACUATION PLANAn emergency evacuation plan should be established for an actual fire alarmcondition. For example, the following steps are

31

SYSTEM NOTES

FOR SERVICE, CONTACT:NX148 LCD CODE PADNX148DASIB98 Rev B (11-01-98)

4ABOUT YOUR SYSTEM, CONTACT THE INSTALLING COMPANY LISTED ON PAGE 12OF THIS BOOKLET.

5GLOSSARY OF TERMSAbort Delay: An option that allows a delay in reporting to the central station.Authority Level: The level of access an individual

6UNDERSTANDING THE LIGHTSArmed LightThe armed light is “on” when the system is armed. The armed light is “off”when it is disarmed. The armed light w

7System ReadyType Code to ArmSystem Not ReadyFor help, press ººSystem ArmedAll Zones SecureCODE PAD FUNCTIONSARMING YOUR SYSTEM IN THE “ON” MODEON is

8System ReadyType code to armMAKING THE SYSTEM READY TO ARMIf the ready light is not on or if it is flashing, a zone is not secure. To identify thisz

9Type code toDisarmDISARMING THE SYSTEMWhen you enter the protected area through one of the designated Entry/Exitdoors, the keypad control will sound